Digital Oilfield Operations Improve with Intelligent Artificial Lift System

oil operations

November 16, 2017

Oil and gas producers have been feeling the pressure in this down market to get the most from their existing assets and wellheads, as efficiently and cost-effectively as possible.

Fortunately, new technologies and capabilities that have been made available through digital oilfield innovation provide the means to effectively squeeze every bit of value from assets. A combination of low-cost sensors, intelligent assets and information tools allow oil and gas producers to gather more data, and have better control of their artificial lift systems. 

These intelligent artificial lift systems can help producers realize three primary business benefits in their wellhead applications:

  • Better visibility into operations
  • Optimized production and asset performance
  • Reduced operating costs

BETTER OPERATIONAL VISIBILITY

Large, multinational oil and gas producers often use downhole sensor systems to monitor underground pressure and temperature. However, many mid- and small-sized producers don’t have the luxury of using these systems, which have high upfront costs and long-term maintenance requirements.

When downhole sensor systems aren’t an option, virtual flowmeters (VFM) provide an economical alternative for understanding underground conditions. VFMs calculate the three-phase flow of water, oil and gas at the wellhead, and provide well analysis for performance improvement. They can calculate the data at either the wellhead site or at the control-system level. 

VFMs do require some upfront calibration, but they’re also a fraction of the cost of downhole sensors, and can produce data of similar accuracy. In fact, one lab test that Rockwell Automation conducted for a major oil producer found the VFMs delivered more than 90% data accuracy compared to actual well-test data. 

Another attractive aspect of VFMs is scalability. This means that the flowmeters can be deployed across multiple lift methods—from highly-productive multi-well pads, to low-producing wells.

OPTIMIZED PRODUCTION

For all of the value that VFMs offer, in truth, they are only valuable if an operator can put the data that is produced to good use. Once an oil and gas producer collects VFM data, they must be able to analyze it, and act on it, to improve operations. 

Some oil and gas producers choose to hire contractors or outside service providers for data collection and data analysis activities. However, many producers prefer to manage data in-house, using business intelligence and analytics software, Fig. 1. 

Business intelligence software integrates data not only from VFMs, but also from all other inputs across an oil field. This creates a single information management and decision support system that can aid all aspects of production. Analytics software provides the means to turn raw data that has been collected into production intelligence.

With these software tools in place, oil and gas producers can tap into the power of their data to optimize their operations. For example VFM data can: 

  • Provide insights into underground conditions, which can be used to drive decisions about reducing bottom-hole pressure or keeping it constant.
  • Be compared against well-test data. This can help verify well-test data, as well as validate planning and production allocation. What’s more, users can improve utilization of test separators by refining and prioritizing test schedules for each well. 
  • Identify underperforming wells. Once such wells are identified, operators can then quickly take any necessary corrective actions to limit production interruptions and deferments, and ultimately stay on track with their production targets.
  • Collect information on system components from different vendors over time. This data can be used to better predict when components, such as a rod, might break. Also, it can improve equipment and supply logistics for maintenance, helping companies be more proactive in getting ahead of downtime issues.

REDUCED OPERATING COSTS 

Intelligent artificial lift systems can help bring down production costs in multiple ways. For example, energy consumption is often overlooked in oil and gas production, which is surprising, given that it’s a significant operational expense. 

Advanced artificial lifts primarily run on electricity, and intelligent systems can collect and analyze data on energy usage to help companies monitor their consumption. The artificial lifts also can be equipped with drives that can regenerate power and put power back on the grid, or they can use solar power to reduce electrical usage. 

Variable speed control also provides another opportunity for cost savings. Traditional lift systems have no speed control. As a result, companies either run the systems until they break, or they turn the systems off, which can result in sand settling into the bottom-hole equipment and clogging it. Either way, oil and gas producers ultimately end up paying for these approaches in the form of costly repairs and unexpected production downtime. Modern artificial lift systems, however, can use variable speed control to help prevent plugging and maximize production efficiency. 

Finally, intelligent artificial lift systems deliver improved insights into operations, which can help companies better manage their capital expenditures. For example, a company considering a well workover can use well data to determine if the potential future yield of a reservoir justifies use of alternative methods to enhance recovery.

TECHNOLOGY IN ACTION: ARC RESOURCES

One example of a successful intelligent artificial lift system application can be found in the vast oil reserves of western Canada. This is the region that ARC Resources calls home. The company is based in Calgary, Alta., and has assets located across Alberta and British Columbia for the exploration, development and production of conventional oil and natural gas. 

In the Montney region of northeastern British Columbia, ARC Resources’ goal was to optimize the control systems for its large, multi-well natural gas production sites. The sites would soon need artificial lift to maintain production levels, but the control systems in place didn’t support the technology. Additionally, ARC Resources wanted to address the expansion and safety challenges that the existing systems presented.

SCALING UP ARTIFICIAL LIFT 

Artificial lift was, by no means, a new concept for ARC Resources. The company’s smaller pads, of up to four wells, already used control systems that supported the use of artificial lift systems for optimizing production as wells depleted. 

However, control systems used on the company’s pads of five or more wells didn’t support artificial lift. The control approach used on these larger pads consisted of multiple controllers that were hardwired together and used in conjunction with remote terminal units (RTUs) to handle the large amount of I/O required to run the entire well pad. 

This rendered the control infrastructure more complex and more mistake prone, and limited the amount of information available for control and monitoring. It also created safety challenges. ARC Resources uses its control architecture to monitor toxic and explosive gases, and to carry out actions such as blocking wells or turning on exhaust fans based on conditions. However, the hardwired controllers could lock up and freeze their outputs, while giving no indication that there was a fault. As a result, the company had to incorporate “watch dog” timer hardware to monitor for these conditions.

ARC Resources chose the ConnectedProduction well manager solution from Rockwell Automation to optimize its larger well pads. The solution includes an Allen-Bradley ControlLogix programmable automation controller (PAC) and FactoryTalk View HMI, which requires no custom coding. The PAC provides single-platform control for sites, with as many as 32 artificial lift wells, and contextualized production information to help operators troubleshoot issues and maintain optimal production levels, Fig. 2.

TRIAL RUN IN BRITISH COLUMBIA

The ConnectedProduction solution implementation began with a pilot project at an eight-well production site in British Columbia.

Fig. 3. ARC Resources is one of the largest operators in the Montney region, and it was here that the company recently decided to begin optimizing the control systems it was using for its large, multi-well natural gas production sites.

ARC Resources is one of the largest operators in the Montney region, and it was here that the company recently decided to begin optimizing the control systems it was using for its large, multi-well natural gas production sites.

 

An early benefit discovered during installation was the solution’s add-on instructions, which helped the team save about two days of programming time. Additionally, integration with other vendor hardware at the site was easy, because the solution uses an open architecture.

Upon its implementation at the eight-well site, the system eliminated the need for multiple controllers and RTUs at the site. Instead, all well pad controls have been consolidated into a single control platform, Fig. 4. This not only simplified the control architecture, but also helped reduce the site’s hardware and software costs.

Additional cost savings were realized from the system because it can support a flow-measurement card within the control panel. This has allowed the site to eliminate its use of a separate flow-measurement computer and save tens of thousands of dollars as a result. The solution also allows the site to use artificial-lift systems, including on/off timers and plunger-lift systems, while also providing visibility into those systems.

Fig. 4. The ConnectedProduction well manager solution gives ARC Resources single-platform control for large sites with up to 32 artifi cial lift wells, and contextualized production information to help operators maintain optimal production levels and troubleshoot issues.

The ConnectedProduction well manager solution gives ARC Resources single-platform control for large sites with up to 32 artifi cial lift wells, and contextualized production information to help operators maintain optimal production levels and troubleshoot issues.
 
“Operators can track events in the ConnectedProduction solution to see what stage we’re in, of the optimization cycle and (they can) make better decisions about what to do next,” said Charlie Kettner, programming specialist for ARC Resources. “Operators can see, for example, that a timer well is not producing anymore, and move to the next step of putting a plunger in the hole.”

The system also is helping ARC Resources enhance safety at the site by reducing the risk of faults going undetected. If something goes wrong with the processor or if an I/O rack comes undone, for example, the control platform can fault to a safe state and shut down all processes. 

Following the successes seen in the pilot project, ARC Resources is planning to extend the ConnectedProduction system to at least four more large multi-well pads that need assisted lift.

Monitoring downhole conditions and equipment performance in artificial lift systems is no longer a cost-prohibitive effort. The digital oilfield is bringing these insights to more oil and gas producers at a low cost with smart and connected artificial lift systems that can help monitor wellhead applications, optimize production, reduce equipment issues and bring down production costs. 

Article by: Srikanth Mashetty, Rockwell Automation

Source: http://www.worldoil.com/magazine/2017/november-2017/special-focus/intelligent-artificial-lift-systems-improve-digital-oilfield-operations

Related Articles


Changing Scene

  • Wesco Opens State-of-the-Art Facility in Eastern Canada to Support Influx of Megaprojects in the Region

    Wesco Opens State-of-the-Art Facility in Eastern Canada to Support Influx of Megaprojects in the Region

    Wesco International has recently announced the grand opening of a new state-of-the-art facility on Higney Avenue in Dartmouth, Nova Scotia, Canada, making this the largest facility of any distributor in the Atlantic region. The new building, facilitated by Touchette Real Estate, a division of Groupe Touchette, will feature Wesco’s comprehensive suite of services and solutions including… Read More…

  • PataBid Nominated for Canadian Choice Award in Software Services

    PataBid Nominated for Canadian Choice Award in Software Services

    PataBid is proud to announce its nomination for a Canadian Choice Award in the Software Services category. This recognition highlights PataBid’s commitment to supporting the electrical contracting community across Canada by providing innovative estimating software solutions that streamline estimating processes and ensure predictable and profitable projects. Read More…


Sponsored Content
The Easy Way to the Industrial IoT

The way to the Industrial IoT does not have to be complicated. Whether access to valuable data is required or new, data-driven services are to be generated, Weidmuller enables its customers to go from data to value the easy way. Weidmuller’s comprehensive and cutting-edge IIoT portfolio applies to greenfield and brownfield applications. Weidmuller offers components and solutions from data acquisition, data pre-processing, data communication and data analysis.

Visit Weidmuller’s Industrial IoT Portfolio.


ADVANCED Motion Controls Takes Servo Drives to New Heights (and Depths) with FlexPro Extended Environment Product Line

Advanced Motion Controls is proud to announce the addition of six new CANopen servo drives with Extended Environment capabilities to their FlexPro line. These new drives join AMC’s existing EtherCAT Extended Environment FlexPro drives, making the FlexPro line the go-to solution for motion control applications in harsh environments.

Many motion control applications take place in conditions that are less than ideal, such as extreme temperatures, high and low pressures, shocks and vibrations, and contamination. Electronics, including servo drives, can malfunction or sustain permanent damage in these conditions.

Read More


Service Wire Co. Announces New Titles for Key Executives

Bruce Kesler and Mark Gatewood have been given new titles and responsibilities for Service Wire Co.

Bruce Kesler has assumed the role of Senior Director – Business Development. Bruce will be responsible for Service Wire’s largest strategic accounts and our growing Strategic Accounts Team.

Mark Gatewood has been promoted to the role of Vice President – Sales & Marketing. In this role, Gatewood will lead the efforts of Service Wire Company’s entire sales and marketing organization in all market verticals.

Read More


Tri-Mach Announces the Purchase of an Additional 45,000 sq ft. Facility

Tri-Mach Elmira Facility

Recently, Tri-Mach Inc. was thrilled to announce the addition of a new 45,000 sq ft. facility. Located at 285 Union St., Elmira, ON, this facility expands Tri-Mach’s capabilities, allowing them to better serve the growing needs of their customers.

Positioning for growth, this additional facility will allow Tri-Mach to continue taking on large-scale projects, enhance product performance testing, and provide equipment storage for their customers. The building will also be the new home to their Skilled Trades Centre of Excellence.

Read More


JMP Parent Company, CONVERGIX Acquires AGR Automation, Expanding Global Reach

Convergix Automation Solutions has completed the acquisition of AGR Automation (“AGR”), a UK-based provider of custom, high-performance automation design and systems integration primarily to the life sciences industry.

Following Convergix’s acquisitions of JMP Solutions in August 2021 and Classic Design in February 2022, AGR marks the third investment in Crestview’s strategy to build Convergix into a diversified automation solutions provider targeting the global $500+ billion market, with a particular focus on the $70 billion global systems integration and connectivity segments. Financial terms of the transaction were not disclosed.

Read More


Latest Articles

  • How Advanced X-Ray and AI Inspection Technologies Optimize Quality Control and Reduce Costs in SMT Manufacturing

    How Advanced X-Ray and AI Inspection Technologies Optimize Quality Control and Reduce Costs in SMT Manufacturing

    Explore how Omron’s latest X-Ray machines and AI-driven solutions are setting new standards in manufacturing efficiency and quality control. The manufacturing landscape is swiftly evolving, and Omron is at the forefront with its innovative PCB inspection machines. These systems offer profound insights into SMT production process, enhanced quality control, and can significantly reduce labor costs. Advancements… Read More…

  • KUKA Establishes New Software and Digital Business Segment

    KUKA Establishes New Software and Digital Business Segment

    Software is playing an increasingly important role in mechanical engineering. What used to be mostly solved mechanically is now done by electronics and the associated software. “With KUKA Digital, we are expanding our offering in order to position ourselves broadly for a market with strong growth potential. Our customers need products, solutions and consulting approaches to digitalize… Read More…