AutomationDirect Adds Motor Control Relays and Intrinsically Safe Relays

March 19, 2020

ProSense motor control relays from AutomationDirect perform specific protective functions for motors or motor components to ensure proper and more efficient operation. Intrinsically safe relays provide safe and reliable control of loads within hazardous locations.

Phase monitor relays provide protection against premature equipment failure caused by faults on 3-phase systems. Phase monitor relays provide protection against phase loss, phase reversal, phase unbalance, undervoltage and overvoltage. These 10A-rated relays, with LED indicator(s), are compatible with Wye or Delta systems and are available in a range of voltage inputs.

Alternating relays are used in special applications where the optimization of load usage is required by equalizing the run time of two loads. These 120 VAC 10A-rated relays are available in SPDT or DPDT configurations; an onboard switch selects alternating or single-load operation.

Pump seal failure relays monitor the shaft seals of submersible pumps. The relay output can be used to give an alarm indication of a leaking seal. The relay will automatically reset when the fault condition clears. These 120 VAC relays include an LED fault indicator and are available for single or two-pump monitoring.

Macromatic intrinsically safe relays allow control of up to four loads with up to four corresponding discrete input devices (switches, sensors, etc.) in hazardous areas. The onboard SPST relays operate at either AC or DC coil voltage ratings. All models offer finger-safe design and include LED status indicator(s) and are 35mm DIN rail or panel mountable.

Learn more by visiting: www.automationdirect.com/relays.

Related Articles

PB-54-Rittal-4SeasonClimateControl2-400.jpg

Rittal Launches the 4 Seasons Climate Control Campaign

The manufacturing world is facing increased challenges like labor shortages, material costs, transportation delays and low stocks, due to the current crisis. To add to that, is the emphasis on raising energy efficiency and lowering the carbon footprint, centering on climate solutions that simplify complex cooling needs through automation and connectivity.

 

 

 

Online Support | Ordering Spare Parts and Accessories – It’s So Simple! | SEW-EURODRIVE

Online Support | Ordering Spare Parts and Accessories – It’s So Simple! | SEW-EURODRIVE

How often have you wondered how to get the right spare parts the fastest? In this case, SEW-EURODRIVE will give you their answer to this question. Take a look at SEW-EURODRIVE’s video now. Want to know more? No problem! They also have a longer version for you with a description of the most important functions of their “Spare parts and accessories” tool in the Online Support.

PBUS-32-Phoenix-THRPCBTerminalBlocks-400.jpg

Phoenix Contact: THR PCB Terminal Blocks up to 2.5 mm²

Phoenix Contact is extending its range of reflow-solder-capable PCB terminal blocks (MSL1) to include the 2.5 mm² cross-section. The new PCB terminal blocks made of heat-resistant plastic are designed for currents up to 32 A and voltages up to 400 V, and are suitable for connecting ferrules up to 2.5 mm² and both rigid and flexible conductors up to 4 mm².

 

 

 

Changing Scene

  • Wesco Opens State-of-the-Art Facility in Eastern Canada to Support Influx of Megaprojects in the Region

    Wesco Opens State-of-the-Art Facility in Eastern Canada to Support Influx of Megaprojects in the Region

    Wesco International has recently announced the grand opening of a new state-of-the-art facility on Higney Avenue in Dartmouth, Nova Scotia, Canada, making this the largest facility of any distributor in the Atlantic region. The new building, facilitated by Touchette Real Estate, a division of Groupe Touchette, will feature Wesco’s comprehensive suite of services and solutions including… Read More…

  • PataBid Nominated for Canadian Choice Award in Software Services

    PataBid Nominated for Canadian Choice Award in Software Services

    PataBid is proud to announce its nomination for a Canadian Choice Award in the Software Services category. This recognition highlights PataBid’s commitment to supporting the electrical contracting community across Canada by providing innovative estimating software solutions that streamline estimating processes and ensure predictable and profitable projects. Read More…

Sponsored Content
The Easy Way to the Industrial IoT

The way to the Industrial IoT does not have to be complicated. Whether access to valuable data is required or new, data-driven services are to be generated, Weidmuller enables its customers to go from data to value the easy way. Weidmuller’s comprehensive and cutting-edge IIoT portfolio applies to greenfield and brownfield applications. Weidmuller offers components and solutions from data acquisition, data pre-processing, data communication and data analysis.

Visit Weidmuller’s Industrial IoT Portfolio.

ADVANCED Motion Controls Takes Servo Drives to New Heights (and Depths) with FlexPro Extended Environment Product Line

Advanced Motion Controls is proud to announce the addition of six new CANopen servo drives with Extended Environment capabilities to their FlexPro line. These new drives join AMC’s existing EtherCAT Extended Environment FlexPro drives, making the FlexPro line the go-to solution for motion control applications in harsh environments.

Many motion control applications take place in conditions that are less than ideal, such as extreme temperatures, high and low pressures, shocks and vibrations, and contamination. Electronics, including servo drives, can malfunction or sustain permanent damage in these conditions.

Read More

Service Wire Co. Announces New Titles for Key Executives

Bruce Kesler and Mark Gatewood have been given new titles and responsibilities for Service Wire Co.

Bruce Kesler has assumed the role of Senior Director – Business Development. Bruce will be responsible for Service Wire’s largest strategic accounts and our growing Strategic Accounts Team.

Mark Gatewood has been promoted to the role of Vice President – Sales & Marketing. In this role, Gatewood will lead the efforts of Service Wire Company’s entire sales and marketing organization in all market verticals.

Read More

Tri-Mach Announces the Purchase of an Additional 45,000 sq ft. Facility

Tri-Mach Elmira Facility

Recently, Tri-Mach Inc. was thrilled to announce the addition of a new 45,000 sq ft. facility. Located at 285 Union St., Elmira, ON, this facility expands Tri-Mach’s capabilities, allowing them to better serve the growing needs of their customers.

Positioning for growth, this additional facility will allow Tri-Mach to continue taking on large-scale projects, enhance product performance testing, and provide equipment storage for their customers. The building will also be the new home to their Skilled Trades Centre of Excellence.

Read More

JMP Parent Company, CONVERGIX Acquires AGR Automation, Expanding Global Reach

Convergix Automation Solutions has completed the acquisition of AGR Automation (“AGR”), a UK-based provider of custom, high-performance automation design and systems integration primarily to the life sciences industry.

Following Convergix’s acquisitions of JMP Solutions in August 2021 and Classic Design in February 2022, AGR marks the third investment in Crestview’s strategy to build Convergix into a diversified automation solutions provider targeting the global $500+ billion market, with a particular focus on the $70 billion global systems integration and connectivity segments. Financial terms of the transaction were not disclosed.

Read More

Latest Articles

  • How Advanced X-Ray and AI Inspection Technologies Optimize Quality Control and Reduce Costs in SMT Manufacturing

    How Advanced X-Ray and AI Inspection Technologies Optimize Quality Control and Reduce Costs in SMT Manufacturing

    Explore how Omron’s latest X-Ray machines and AI-driven solutions are setting new standards in manufacturing efficiency and quality control. The manufacturing landscape is swiftly evolving, and Omron is at the forefront with its innovative PCB inspection machines. These systems offer profound insights into SMT production process, enhanced quality control, and can significantly reduce labor costs. Advancements… Read More…

  • KUKA Establishes New Software and Digital Business Segment

    KUKA Establishes New Software and Digital Business Segment

    Software is playing an increasingly important role in mechanical engineering. What used to be mostly solved mechanically is now done by electronics and the associated software. “With KUKA Digital, we are expanding our offering in order to position ourselves broadly for a market with strong growth potential. Our customers need products, solutions and consulting approaches to digitalize… Read More…